Experiments in Technical Analysis

[softtouch]

yaar finally suspense pe se parda uthao aur bolo aakhir ye code kiska hai thakur.......ashish ya karthik ?

 

[aca_trader]

yaar finally suspense pe se parda uthao aur bolo aakhir ye code kiska hai thakur.......ashish ya karthik ?

Ashish in question (aca_trader) does not know how to write codes. It's Karthik's only.

Best Regards,
--Ashish

 

[asnavale]

There is nothing other than the symbol ^NSEI, I have attached the file.
Raj

Hi Raj,

I asked for the Symbols page because the earlier file showed something else. In the earlier file on first page, in the analyis window snapshot the entry under Ticker (first column), it shows "<P...". Therefore, I asked for it. I have run the test and attached the full report except the graphs with this post. Compare each page with what you are getting. You may be able to identify the problem. The attached file includes the AFL code also. Compare the formula with what you have used. Check your NIFTY data also. Post your comments and observations.

Regards

-Anant

 

[indrag91]

Hi Raj,

I asked for the Symbols page because the earlier file showed something else. In the earlier file on first page, in the analyis window snapshot the entry under Ticker (first column), it shows "<P...". Therefore, I asked for it. I have run the test and attached the full report except the graphs with this post. Compare each page with what you are getting. You may be able to identify the problem. The attached file includes the AFL code also. Compare the formula with what you have used. Check your NIFTY data also. Post your comments and observations.

Regards

-Anant

Sir
Thanks a lot
I have followed the parameters in ur settings page, but still.. still... some mistake is going on in my side, pls go thro my settings (printed screens) if u find any fault pls tell me. sorry to disturb u so much.(2 doc files)
Raj

 

[asnavale]

Sir
Thanks a lot
I have followed the parameters in ur settings page, but still.. still... some mistake is going on in my side, pls go thro my settings (printed screens) if u find any fault pls tell me. sorry to disturb u so much.(2 doc files)
Raj

Hi Raj,

I think I have figured out the mistake. See your attached file 'backtest.doc'. On the second page where you have a snapshot of 'back tester settings-general' look at the entry 'Min. shares'. You have entered it as 100. As the program is taking NIFTY values as price, you need at least 100 times the NIFTY value (which is not less than 3.5 lakhs) as initial equity. But your initial equity is only 20,000. So no trade can be initiated with this small amount. That is why there are no trades. Just change the Min shares to 1 and you should be able to get the results. Do this change and report your results.

Regards

-Anant

 

[ashutosh.krsrivastava]

This is for Ami ,as he posted .

Asish

Hey Asish,
i tried to run the program. I saved the file as .afl in custom folder. when i try to run, i get blank screen. I have got about 3 months of data in my amibroker. Wht may be the reason??

regards
ashutosh

 

[uasish]

Hey Asish,
i tried to run the program. I saved the file as .afl in custom folder. when i try to run, i get blank screen. I have got about 3 months of data in my amibroker. Wht may be the reason??

regards
ashutosh

The code language was of Ami,i use only Metastock,can't contribute anything regarding Ami.

Asish

 

[ashutosh.krsrivastava]

Asish

Now this will get more interesting. I am enclosing the Mabiuts K1 afl.
Looking forward to your inputs.

regards

Karthik

Hey kartik,
i am unable to use this mabiuts k1 afl. I have got about 3 months of data, but the screen in my ami is blank when i run the afl. Also i saw that there is no _SECTION_END() in the bottom of the program. I am not wellversed with ami programming but should'nt there be any section end?? pls help me here, why am i getting blank screen??

 

[indrag91]

Hi Raj,

I think I have figured out the mistake. See your attached file 'backtest.doc'. On the second page where you have a snapshot of 'back tester settings-general' look at the entry 'Min. shares'. You have entered it as 100. As the program is taking NIFTY values as price, you need at least 100 times the NIFTY value (which is not less than 3.5 lakhs) as initial equity. But your initial equity is only 20,000. So no trade can be initiated with this small amount. That is why there are no trades. Just change the Min shares to 1 and you should be able to get the results. Do this change and report your results.

Regards

-Anant

Thanks Mr.Anant,
It is now working well, and i have attached the report. The only differance is even though i have give the date range from 01-01-06 to 04-04-07, it is taking only the trades from 13-03-2006. Any how i have tested the system and getting 20% gain in my test.
Once again thanks for your guidance.
Congracts for ur work, keep on doing.
Raj

 

[karthikmarar]

Hey kartik,
i am unable to use this mabiuts k1 afl. I have got about 3 months of data, but the screen in my ami is blank when i run the afl. Also i saw that there is no _SECTION_END() in the bottom of the program. I am not wellversed with ami programming but should'nt there be any section end?? pls help me here, why am i getting blank screen??

Ashutosh

I am sorry .. the afl posted earlier was for backtesting the Mabiuts K1.
I am enclosing the afl for the chart with buy and sell condition. Regret the inconvenience caused.

warm regards

Karthik